Do not have this car but here's a thought::: TPS should be on the side of throttle body plate shaft, probably opposite side of the throttle cable mounting box.
Type: Posts; User: jimclemjr
Do not have this car but here's a thought::: TPS should be on the side of throttle body plate shaft, probably opposite side of the throttle cable mounting box.
How many miles and hours? Size of tires and any CVT upgrades? Have you been riding mud or deep water? Does it in Low and High?
If now Yamaha is saying use the poly.....IIRC when I researched the grease a while ago, one of the qualities of this grease was its water resistance, so if this is to be used there should be little...
This forum is not typically about cars. It is about UTVs. The forum orginator's nickname was HotRod.
will not blow up, but probably run rich and create some carbon buildup and the challenges that may cause over time. But the MSD can be tuned to the proper AFR if you have an AFR gauge or get someone...
I don't like the sloop in the splines but might as well ride it out. Make sure washer is on correctly and nut properly tightened to eliminate ANY movement in the mating. I would sand the clutch shoes...
Picture of the wet clutch drum please. Would rather see drum to make final assessment due to high cost of clutch unit. If memory serves, EPI did have wet clutch springs that were heavier and used for...
I would think you need to get into it and check primary weight and secondary function. Watch the videos and educate yourself before you start, and make sure you have the Yamalube in hand as I...
54 MPH sounds like you now have full throttle which you would really need with the load. The weights keep it in 'Low" gear longer and will help but it sounds like weights are not backshifting or the...
I have not pulled an X machine but for Gen 1 with the motor out and carrier off, it was not too bad to do the seal. Not so sure how much room you have without the dump bed. But once you slide the...
Check your ground cable to the motor and if it's good then do the decompressor soon. $.02
I have a powered RAM mount for my Samsung tablet that came with a 12v power plug. I installed a 12v powered outlet that is constantly on to keep tablet from doing it's off and on routine when we...
A buddy found some alum wheel adapters on eBay so he could put on his wildcat to use other standard five lug wheels. That might be worth checking out.
I have talked to James before about doing the two weights and he did not think it was a big deal when weights matched and close in value. The weights exert pressure based on the G forces of the...
You could also think about getting 16G and 18G weights. When you mix them equally you get a 17G effect so it gets you one more tuning option. I do not remember seeing anything negative about this...
It looks like a good combo to me, prob could jump a size up in tires if you lose a couple passengers in future.
There is an advantage to doing a shim...as the belt wears and drops some you can pull the shim and it puts you close to original bottom end. You can do that about time to service the secondary.
Check out the SXS Blog guys on YouTube, they are swapping a TurboS motor in their RS1 and it will be rolling soon if not already. Some active insanity lol.
With that big heavy machine and assuming you meant 100 miles since new on Viking not your riding time, if it were 'slipping' you would probably hear a bunch of chirping and squealing. If something is...
I would check the service manual for that question.
I would say that depends on your riding style and goals. You will now doubt get more power and torque and the motor will be ready to scream, if you are after top speed then the Grizzly gearing may...
from my experience in messing with my spark arrestor pee spout, the 708 really breathes and if you open exhaust up any you had better retune the fuel map.......I would guess the same is true for the...
the offset is a measurement from the center of the wheel. so if it is a 6" wheel and a 1" from the outside edge of the wheel from the outer rim, then 3"- 1" = 2" offset from the center. Or a about...
If someone put it on with red Loctite then you need to heat it.
Put on outer primary and use a holder on it and try to grab nut remnant with a small pipe wrench or vise grips. Can't remember how...
If you put the stroker in it you may start to think twice about needing the 850. Did you discuss the Viking VI cam with James? with a couple of other mods that would cost you a few hundred $$$ it...