Search:

Type: Posts; User: trevor-t

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    2,381

    Thank you Keeter, I came close to cutting wires,...

    Thank you Keeter, I came close to cutting wires, but it is still all original and the high beams are working without blowing the fuse. Switch has been cleaned and reinstalled, nothing out of place...
  2. Replies
    6
    Views
    2,381

    Hi again, should have asked, was that short at...

    Hi again, should have asked, was that short at one of the 3 pin connectors near the lights? Male or female? Will take a closer look.
    Thanks again
    Trevor T
  3. Replies
    6
    Views
    2,381

    Well, that is not good to hear Keeter, but good...

    Well, that is not good to hear Keeter, but good to know that you resolved your problems, although it sounds a bit expensive for me. I can see me rewiring the lights outside of the origial harness...
  4. Replies
    6
    Views
    2,381

    Hi Beams blow fuse - con"fused" again

    Our '06 660 has another electrical gremlin, may have been there for awhile as we are rarely out after dark; but a few nights ago we were visiting just up the road and had to creep home without...
  5. Replies
    30
    Views
    9,099

    Hi, haven't figured out how to do the quote...

    Hi, haven't figured out how to do the quote stuff, but to clarify for mfrench,my signal fuse brown wire had a direct short to grd before it reached the connector to the brake switch, so the fuse blew...
  6. Replies
    30
    Views
    9,099

    It is done, so far so good, we have stop lights...

    It is done, so far so good, we have stop lights and it cranks in gear with the brakes on..
    Someone had added a winch and left the wires from the batt to the solenoid way too long so they have been...
  7. Replies
    30
    Views
    9,099

    Hi again, my plan is to cut that...

    Hi again,
    my plan is to cut that brown just after its fuse, join the new wire under the fuse box, then cut it again just before the brake switch connector and reconnect with the new...
  8. Replies
    30
    Views
    9,099

    Hi again, yes, it cranks and starts in Neutral...

    Hi again, yes, it cranks and starts in Neutral fine; just no brake lights or starting in gear.
    The digi display all works, so I do not know what else this brown circuit supplies. Seems to be...
  9. Replies
    30
    Views
    9,099

    Update..

    So far have not found where that brown wire has gone to ground, there are some unused connectors behind the dash, near the steering, but nothing looks distressed. Will take a look under the engine...
  10. Replies
    30
    Views
    9,099

    No problem Timmi, but don't think I had...

    No problem Timmi, but don't think I had attachments. Soon be up to 10 posts at this rate.
    Cheers
    Trevor
  11. Replies
    30
    Views
    9,099

    Thought I had posted an update a few hours ago, I...

    Thought I had posted an update a few hours ago, I must be doing something else wrong...
    Test bulb across the signal fuse there is only .4v from the Br wire to grd., not enough to light up the stop...
  12. Replies
    30
    Views
    9,099

    Sat. pm update

    Jumper wires used and...
    with the test light, 25w, in there is only .4v potential in the brown wire because of the short, so nothing works, brake lights or starter solenoid.
    I tested (carefully)...
  13. Replies
    30
    Views
    9,099

    Thanks Steve, that was in my plan, not being...

    Thanks Steve, that was in my plan, not being electrical I will have to make up a jumper, it has been a long time...
    All of the other sensors are working just lost the brake lights and start in gear,...
  14. Replies
    30
    Views
    9,099

    Good morning, I hear you...

    Good morning,
    I hear you about the "aging thing", been retired for a few years now; good to hear from you Steve, I was getting worried.
    Yes, I have found the manual and the...
  15. Replies
    30
    Views
    9,099

    Only had it for a couple of weeks, but no sign...

    Only had it for a couple of weeks, but no sign of mice damage, at least yet..
    Looks good under the fuses, somewhere there's a strong ground on that brown wire, but it also has continuity to the...
  16. Replies
    30
    Views
    9,099

    Hi, I have been reading and upgrading the...

    Hi, I have been reading and upgrading the grounding strategy is on my list, but at the moment that small gound and connector look good, certainly not overheated.
    The only things not working are the...
  17. Replies
    30
    Views
    9,099

    Help - signal circuit short

    Hi, I am the new owner of a Rhino 660 and while it is in pretty good shape it has some issues that need to be taken care of.
    It was initially tricky to get the "N" light on and annoying that it...
  18. Replies
    4
    Views
    1,461

    New toy for old folks...

    Hi from Durham, Ontario,
    We have owned our 2005 660 Rhino for 1 week and are looking forward to doing some exploring. It is in pretty good shape, but does have...
Results 1 to 18 of 18