» Today's Birthdays

None

Search:

Type: Posts; User: jimclemjr

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    481

    This forum is not typically about cars. It is...

    This forum is not typically about cars. It is about UTVs. The forum orginator's nickname was HotRod.
  2. Replies
    1
    Views
    473

    will not blow up, but probably run rich and...

    will not blow up, but probably run rich and create some carbon buildup and the challenges that may cause over time. But the MSD can be tuned to the proper AFR if you have an AFR gauge or get someone...
  3. Replies
    25
    Views
    2,225

    I don't like the sloop in the splines but might...

    I don't like the sloop in the splines but might as well ride it out. Make sure washer is on correctly and nut properly tightened to eliminate ANY movement in the mating. I would sand the clutch shoes...
  4. Replies
    25
    Views
    2,225

    Picture of the wet clutch drum please. Would...

    Picture of the wet clutch drum please. Would rather see drum to make final assessment due to high cost of clutch unit. If memory serves, EPI did have wet clutch springs that were heavier and used for...
  5. Replies
    25
    Views
    2,225

    I would think you need to get into it and check...

    I would think you need to get into it and check primary weight and secondary function. Watch the videos and educate yourself before you start, and make sure you have the Yamalube in hand as I...
  6. Replies
    25
    Views
    2,225

    54 MPH sounds like you now have full throttle...

    54 MPH sounds like you now have full throttle which you would really need with the load. The weights keep it in 'Low" gear longer and will help but it sounds like weights are not backshifting or the...
  7. Replies
    7
    Views
    540

    I have not pulled an X machine but for Gen 1 with...

    I have not pulled an X machine but for Gen 1 with the motor out and carrier off, it was not too bad to do the seal. Not so sure how much room you have without the dump bed. But once you slide the...
  8. Replies
    3
    Views
    939

    Check your ground cable to the motor and if it's...

    Check your ground cable to the motor and if it's good then do the decompressor soon. $.02
  9. Replies
    11
    Views
    1,213

    I have a powered RAM mount for my Samsung tablet...

    I have a powered RAM mount for my Samsung tablet that came with a 12v power plug. I installed a 12v powered outlet that is constantly on to keep tablet from doing it's off and on routine when we...
  10. Replies
    7
    Views
    697

    A buddy found some alum wheel adapters on eBay so...

    A buddy found some alum wheel adapters on eBay so he could put on his wildcat to use other standard five lug wheels. That might be worth checking out.
  11. Replies
    98
    Views
    9,556

    I have talked to James before about doing the two...

    I have talked to James before about doing the two weights and he did not think it was a big deal when weights matched and close in value. The weights exert pressure based on the G forces of the...
  12. Replies
    98
    Views
    9,556

    You could also think about getting 16G and 18G...

    You could also think about getting 16G and 18G weights. When you mix them equally you get a 17G effect so it gets you one more tuning option. I do not remember seeing anything negative about this...
  13. It looks like a good combo to me, prob could jump...

    It looks like a good combo to me, prob could jump a size up in tires if you lose a couple passengers in future.
  14. Replies
    98
    Views
    9,556

    There is an advantage to doing a shim...as the...

    There is an advantage to doing a shim...as the belt wears and drops some you can pull the shim and it puts you close to original bottom end. You can do that about time to service the secondary.
  15. Thread: Rs1

    by jimclemjr
    Replies
    6
    Views
    739

    Check out the SXS Blog guys on YouTube, they are...

    Check out the SXS Blog guys on YouTube, they are swapping a TurboS motor in their RS1 and it will be rolling soon if not already. Some active insanity lol.
  16. Replies
    5
    Views
    561

    With that big heavy machine and assuming you...

    With that big heavy machine and assuming you meant 100 miles since new on Viking not your riding time, if it were 'slipping' you would probably hear a bunch of chirping and squealing. If something is...
  17. Replies
    5
    Views
    669

    I would check the service manual for that...

    I would check the service manual for that question.
  18. Replies
    5
    Views
    669

    I would say that depends on your riding style and...

    I would say that depends on your riding style and goals. You will now doubt get more power and torque and the motor will be ready to scream, if you are after top speed then the Grizzly gearing may...
  19. from my experience in messing with my spark...

    from my experience in messing with my spark arrestor pee spout, the 708 really breathes and if you open exhaust up any you had better retune the fuel map.......I would guess the same is true for the...
  20. Thread: Stock offset

    by jimclemjr
    Replies
    9
    Views
    740

    the offset is a measurement from the center of...

    the offset is a measurement from the center of the wheel. so if it is a 6" wheel and a 1" from the outside edge of the wheel from the outer rim, then 3"- 1" = 2" offset from the center. Or a about...
  21. Replies
    2
    Views
    513

    If someone put it on with red Loctite then you...

    If someone put it on with red Loctite then you need to heat it.
    Put on outer primary and use a holder on it and try to grab nut remnant with a small pipe wrench or vise grips. Can't remember how...
  22. Replies
    8
    Views
    1,400

    If you put the stroker in it you may start to...

    If you put the stroker in it you may start to think twice about needing the 850. Did you discuss the Viking VI cam with James? with a couple of other mods that would cost you a few hundred $$$ it...
  23. Replies
    1
    Views
    777

    Maxxis and Discount Tire Shoutout

    I want to tell a little story to give a positive shout-out for Maxxis Tires and Discount Tire Co. This story also makes a point of persistence is sometimes necessary. In 01/2018 I bought a set of...
  24. Replies
    8
    Views
    1,278

    James deshrouded the head and that brings the...

    James deshrouded the head and that brings the compression down a few points so it is probably actually a little over 10.5:1. I was going to go with the stroker but would have had to wait several...
  25. Replies
    8
    Views
    1,278

    Definitely do the reverse upgrade, its only $75...

    Definitely do the reverse upgrade, its only $75 for the part and a hassle to split the cases but an opportunity to check all internals. My signature shows my motor that James built for me a few years...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Powered by vBadvanced CMPS v4.2.1