This guy originally came to me about 3 weeks ago and said he wanted a 4seat cage he could swap in between seasons.He has a full cab for plowing snow but wanted a fun 4 seat cage for the family on the off season.What I didn't realize was there is no cage bung support for this model.I had to have one off bungs made for the A pillar and I fixed the less than good B pillar attachment.I'm not quite sure what they were thinking there from factory but I wasn't about to fallow in their foot steps.Looks goofy in the front but he has a friend that he wanted to do the sheet metal work for the roof and filler panel between the dash and dash bar.I couldn't really chop the cage the way he wanted because the bed set so much higher than the front seat and he wanted adults to fit in the back.SO I was after the elision that it was chopped.I'll try to get him to send me pics after the sheet work is done.
|
Sponsored By: |
 |
Thanks: 0
Likes: 1
Results 1 to 10 of 11
Thread: XP900 Ranger 4 seat cage
-
03-07-2014, 01:25 AM #1Vendor
- Join Date
- Dec 2013
- Location
- Rockford OH
- Posts
- 544
XP900 Ranger 4 seat cage
08 Resurrected Rhino build and your custom SXS fabrication shop @ Baxter Built Fabrications. Give me a call at 419-953-8509 if you have any questions.
-
Post Thanks / Like - 0 Thanks, 1 Likes
WV Hot Rod Rhino liked this post
-
03-07-2014, 01:29 AM #2Vendor
- Join Date
- Dec 2013
- Location
- Rockford OH
- Posts
- 544
It's tabbed out so that all OEM hardware is used between both cages.There is way more stuff mounted to the B pillar of this thing than I thought.Engine and CVT breather,back fire wall,seat back,and door/seat bars all needed to fit the new cage.
08 Resurrected Rhino build and your custom SXS fabrication shop @ Baxter Built Fabrications. Give me a call at 419-953-8509 if you have any questions.
-
03-07-2014, 01:46 AM #3
- Join Date
- Dec 2013
- Location
- Musella, Ga.
- Posts
- 250
nice work ....looks like a lot of time/work getting every thing in place , all your cage's look great
2007 SE 660, Hotrods 4mm crank, Wisco 2 over 10/1 piston, head ported w/ +2mm valves, mud buster cam, billet middle gear support, JBS sheave 14g /purple spring, friction washers, slugged wet clutch +6 grams, Gibson header & muffler, 4000 lb winch, hi-flow fuel pump, K&N air filter/w pro-flow adapter, A/F gauge, 3in lift, 26 mud-lites, snorkeled, floor board guards, JBS radiator guards, fender flare's, rzr seats
-
03-07-2014, 03:14 AM #4
- Join Date
- Dec 2013
- Location
- strong maine
- Posts
- 1,557
very nice work!
07 sport 720 stroker, +4mm hot rods stroker crank ( welded ) weller head studs, 43mm fcr carb,alba high flow fuel pump, weller high flow fuel line kit, billet middle drive support 102mm 10:1 JE piston stage 1 raptor cam, ported & polished head & intake manifold, k&n full intake, alba exhaust, 700 cam plate JBS sheave 14g od's orange spring antifriction washers,700 belt, rhino giant 4 seat cage, 26" big horns on raceline beadlocks, homemade diamond plate alum. half doors....an more!
-
03-07-2014, 03:33 AM #5
- Join Date
- Dec 2013
- Location
- Kenova W.V
- Posts
- 2,784
Nice looking work
Sent from the drivers seat of my truck.
JBS 787, bored throttle body , +1ported head, JBS deshrowded valves,kibble white valve springs, muzzy exshaust,dynatek coil,TCP oil cooler, triple pass radiator,billit one steering rack,heavy duty steering tierods, heim joints,+6 long travel,tilt wheel, radius roll cage, JBS rear splash shield
Bead lock wheels , bear claw tires , power steering
-
03-07-2014, 04:46 AM #6Super Moderator
- Join Date
- Dec 2013
- Location
- Clayton, Mi
- Posts
- 3,256
Nice work. It'll look great once it's painted.
Commander 1000
Kawasaki Prairie 400
Suzuki Ozark 250
Suzuki 230
F-250 6.0 Diesel
-
03-07-2014, 06:39 AM #7Administrator
- Join Date
- Dec 2013
- Location
- Mount Hope, West Virginia, United States
- Posts
- 8,709
lookin good!!
James Davis
If you have questions call me!!!
304-673-2602
304-877-3419
Check out our web https://jbsperformance.com/
Email to - jbsperformanceinc@aol.com
Ship to - 131 Davis Ct., Mt. Hope, WV 25880
-
03-07-2014, 07:26 AM #8
- Join Date
- Dec 2013
- Location
- frostburg md
- Posts
- 4,019
great work
07 camo 660,yoshi duals,kms intake,dynatec cdi,jet kit, montana jack f&r winch mount,w/ warn xt40, 27" bighorns,2" lift, cab with summit heater,aux red top optima, 5 bad ass jrt's on board,itp ss 212s, jbs sheave,14 gr. wts,orange spring, 40 " led light bar, autometer guages,equus tach,innovate afm, jensen ms30 ,jbl 6.5s, elka stage 1 shocks, kenwood 2way radio, alpine ktp445u amp, led headlight mod,twisted stitch harnesses,pro1 doors, 60 amp alternator,power steering, pc925 battery
-
03-07-2014, 09:25 AM #9
- Join Date
- Dec 2013
- Posts
- 376
Looking good as usual Baxter
when in doubt throttle it out
-
03-07-2014, 12:31 PM #10Vendor
- Join Date
- Dec 2013
- Location
- Mt. Pleasant , Pa
- Posts
- 1,300
Looks good. It should keep everyone nice and safe
2016 YXZ Yellow SE
old ride 2 11 Polaris RZR XP 900 White Lightning Edition all stock for now.
old old ride. 06 JBS built 686 , Benachmark ported head , Falicon rod , JBS sheave , Alba pipe and fuel pump , custom cage , HID head lights , 26" GBC Dirt Tamers on SS212 wheels , Superwinch Terra 45 w/ Synthetic Rope , Dynatek CDI
Reply With Quote
Bookmarks