-
Any Reloaders Using Bullet Feeders??
I picked up an RCBS Pistol Bullet Feeder for one of my Pro2000 presses and was wondering if anyone else is using them. Any tip or tricks in setting it up? I opened the box but have not looked it over real good yet. I plan to set it up this weekend and try it out on some 9mm. If it works as good as they claim it to I should be able to pump out over 1,000 rounds an hour. Any words of wisdom will be greatly appreciated.
Benchmark built 720 Stroker (2007 Camo 660) - JE 102mm Pro Series 10:1 Piston, +4 Stroker Crank, Ported & Polished Head, Kibblewhite +1 Valves, Kibblewhite Valve Springs, Raptor Stage II Cam, billet middle drive plate, JBS HotRod Sheave, 14gr OD weights, Orange Spring, weighted Airdam clutch shoes, Dynatek CDI & Hot Coil, Muzzy Dual Exhaust, FCR41 Carb, 700 Cam Tensioner, Mishimoto Radiator with TCP Shroud and Spal Fan, Alba Fuel Pump, 27.5" Pitbull Rockers, EZ Steer and Snorkels
-
No one loads their own ammo? Surprises me, figured there would be a ton of reloaders.
Benchmark built 720 Stroker (2007 Camo 660) - JE 102mm Pro Series 10:1 Piston, +4 Stroker Crank, Ported & Polished Head, Kibblewhite +1 Valves, Kibblewhite Valve Springs, Raptor Stage II Cam, billet middle drive plate, JBS HotRod Sheave, 14gr OD weights, Orange Spring, weighted Airdam clutch shoes, Dynatek CDI & Hot Coil, Muzzy Dual Exhaust, FCR41 Carb, 700 Cam Tensioner, Mishimoto Radiator with TCP Shroud and Spal Fan, Alba Fuel Pump, 27.5" Pitbull Rockers, EZ Steer and Snorkels
-
I reload 17 rem., 223,22-250 ,45,45 lc, 44mag,and 500 mag, but I just use an rcbs single stage , sounds like you have a nice setup, most of my rifles are varmint guns so i'm loading for small groups and not so much on the volume
07 camo 660,yoshi duals,kms intake,dynatec cdi,jet kit, montana jack f&r winch mount,w/ warn xt40, 27" bighorns,2" lift, cab with summit heater,aux red top optima, 5 bad ass jrt's on board,itp ss 212s, jbs sheave,14 gr. wts,orange spring, 40 " led light bar, autometer guages,equus tach,innovate afm, jensen ms30 ,jbl 6.5s, elka stage 1 shocks, kenwood 2way radio, alpine ktp445u amp, led headlight mod,twisted stitch harnesses,pro1 doors, 60 amp alternator,power steering, pc925 battery
-
same here. rcbs single stage press. i know its slow but i go for accuracy. so far ive only loaded for target, varmint and big game. i havent tried reloading for pistols yet
Sent from my iPhone using Tapatalk
CASPAR
2016 Yamaha Wolverine R-Spec (camo)
Yamaha roof, Yamaha folding windshield, Yamaha fender flares, Yamaha heavy duty front and rear bumpers, Yamaha toolbox, Yamaha vinyl rear window. JBS sheave and slug kit (18g sliders for now) 28x10x14 blackwater evolution tires on 14 inch MSA M26 dark tint vibe wheels, Superwinch 4,500lb winch, 2-32 inch light bars on front, light pods on pillars, 32 inch ligh bar on back, eagle eye backup lights, homemade led whips,
-
A Very Bad Monkey
I have a couple of progressive presses but they only have case feeders.
2014 Green EPS Viking
Superwinch 4500
Denali Pro Plow
27" Interforce F & 28" Zillas R
ITP Delta 5+2 Wheels
Spring Spacers
UTV HQ Vent Windshield & Encl
EMP Wiper & Rear Bumper
Summit Racing Heater
YXZ SE Seats
JBS Guards,Skids & Sheave
4-Point Harnesses
Ultra Halogen Headlights
24" Light Bar
Power Sub-Panel
LEDXTREME Whip
Backup Camera & CREE Lights
Accent LEDs
Sound Dampening Kit
Center Console
Seizmik Mirrors
Extinguisher
TSC Bed Mat
Spare Carrier
-
^^^x2....I have a 550 with a case feeder ; but , "I'm" the bullet feeder . lol
08 700 ...
-
Double T Mudbusters
father in law passed a few yrs ago. He had the easy for me to read powder charge books and single stage setup, scales tumbler etc. i really need to get his out for my .270 30-30 and get my dad back to 195+ grains in his 8mm mauser. he taught me how to use it and make consistent shells for my .270 with 150 gr, it went from crap wanting to sell it to tearing up snuff cans at 100 yrds overnight
2012 blue 700
JBS Stage 2 Extreme sheave: 15gram sliders: gold spring: Dynatek: JBS splash guards: JBS Slugged clutch: 30x9/10x14 Monster Mayhem: 14" ss212: 2"+ JD lift: 4500lb champion winch: hyperlube radiator treatment: rzr seats-JD lowered: JD 3" cage chop: blue underglows/dome light: JD aluminum roof: JD tower speaker bar with 4 1/2" and bluetooth amp: 42" light bar forward cubes rear: Half windshield: Snorkel your UTV by JD:
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
I hear ya, I use single stage presses for my rifles and low volume stuff. Mainly use the progressives for 9mm, 40 and 45ACP and the normal 44 mag stuff. I hope to have the bullet feeder setup this weekend. If I could automate the case feeding I would not even have to be in there.
Benchmark built 720 Stroker (2007 Camo 660) - JE 102mm Pro Series 10:1 Piston, +4 Stroker Crank, Ported & Polished Head, Kibblewhite +1 Valves, Kibblewhite Valve Springs, Raptor Stage II Cam, billet middle drive plate, JBS HotRod Sheave, 14gr OD weights, Orange Spring, weighted Airdam clutch shoes, Dynatek CDI & Hot Coil, Muzzy Dual Exhaust, FCR41 Carb, 700 Cam Tensioner, Mishimoto Radiator with TCP Shroud and Spal Fan, Alba Fuel Pump, 27.5" Pitbull Rockers, EZ Steer and Snorkels
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
I've seen a bunch of those videos where the guys "automated" them. They look pretty cool an all ; but , one bad case , or one unfed primer , and you have a mess !! I'll stick to my manual index !
08 700 ...
-
Post Thanks / Like - 0 Thanks, 1 Likes
Bookmarks