-
04-18-2019, 09:18 PM
#101
That is looking really nice so far. Are you doing a window in the back, or just a door to get into the bed from the back? Either way, that will be a lot of nice storage and look good to. You know, the factory bed was the biggest turn off for me on the Wolverine. I think they look a little out of place, but they do look much better with a bed cover on.
JBS 734 with Crank Works crank and rod - CP 11:1 BBK- Hotcams stage 3 Raptor cam - JBS ported head - JBS Hot Rod sheave with 16s - Gold secondary - 26x9 OG Bighorns on Racline wheels - BRP cdi - Bazzaz Z FI - Yoshimura exhaust - Hump's led headlight swap with Trailbrightled lights - 10" Rigid SR light bar - 4" cage chop with home made custom bracing - home built doors - Mishimoto radiator
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
04-18-2019, 09:54 PM
#102
Thanks Hump. No window but ill have a backup camera, it has a door with a yet to be installed gas assist lifter.
Things left to do are.
1. install/weld a cover over the backup camera to protect it.
2. install the rubber latches on the door.
3. install the antenna.
4. install the bed tie down hooks.
5. Fab and install the tie piece between the bed floor and the plastic behind the seats.
6. install the 2way radio.
7. install the bazooka and controller.
8. install gas assist lifter.
9. install/weld door rain seal.
10. drill holes and add grommets in the cage to run the wiring.
11. wire everything up.
12. change out bearings in pass rear wheel already done the others.
13. install the rear rhino axles, put fronts in last weekend.
14. change diff fluids.
15. trim sides of roof and install it and the windshield.
16. weld mounts, install whip lights and wire them.
17. install high mounted backup lights and weld protective hoods.
Im sure im missing some things, lol.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
04-18-2019, 10:05 PM
#103
pic with the door installed.
After the ride it will get some more welds then off to powder coat as long as everything is okay, the bed sides and back will get the camo and the top sides will just be black with maybe some graphics. maybe a place to put stickers where I've rode. still thinking about it.
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
04-21-2019, 06:21 PM
#104
-
04-21-2019, 07:53 PM
#105
Few more pics. Big thanks to James, Bitty, Nikki, Ryan and Demion. And everyone else that lended a hand
Sent from my SM-G955U1 using Tapatalk
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
06-21-2019, 08:16 AM
#106
Timmy i need your knowledge. just picked up a set of YXZ seats and the driver side bolts right up but the passenger side bolt holes do not. Ive never heard of anyone saying anything about this.
-
06-21-2019, 08:31 AM
#107
Ridin' and Guidin'
are you talking about the cushions or the holes to mount to the floor? the cushion backs are all the same
Originally Posted by
HillbillyStyle
Timmy i need your knowledge. just picked up a set of YXZ seats and the driver side bolts right up but the passenger side bolt holes do not. Ive never heard of anyone saying anything about this.
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
-
06-21-2019, 08:32 AM
#108
The frame that mounts to the floor.
-
06-21-2019, 08:43 AM
#109
Ridin' and Guidin'
I am almost certain Viking and Wolverine are same mount holes, not sure about YXZ if that's what frames you have.
Originally Posted by
HillbillyStyle
The frame that mounts to the floor.
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
-
06-21-2019, 08:49 AM
#110
Im trying to install the whole YXZ seat frame and all. are you saying the cushions and backs from the YXZ mount to the wolvy seat frames?
Bookmarks