Supposed to be 2.. when they both come out the screen moves and the screws go to the inside... mine was on the inside of the screen towards the throttle body
Sent from my Moto G Play using Tapatalk
Sponsored By: |
Supposed to be 2.. when they both come out the screen moves and the screws go to the inside... mine was on the inside of the screen towards the throttle body
Sent from my Moto G Play using Tapatalk
James Davis
If you have questions call me!!!
304-673-2602
304-877-3419
Check out our web https://jbsperformance.com/
Email to - jbsperformanceinc@aol.com
Ship to - 131 Davis Ct., Mt. Hope, WV 25880
Looks like one of mine got sucked through the throttle body hit the top of the valve the valve shot it back up in the head above the valve and made a mark so I'm going to have to pull the head off and see if there is valve damage.... going to do a leak down test first though
Sent from my Moto G Play using Tapatalk
James Davis
If you have questions call me!!!
304-673-2602
304-877-3419
Check out our web https://jbsperformance.com/
Email to - jbsperformanceinc@aol.com
Ship to - 131 Davis Ct., Mt. Hope, WV 25880
James Davis
If you have questions call me!!!
304-673-2602
304-877-3419
Check out our web https://jbsperformance.com/
Email to - jbsperformanceinc@aol.com
Ship to - 131 Davis Ct., Mt. Hope, WV 25880
This thing bugged me and I went back and looked at my filter. Keep in mind I bought my Wolv used with 700 miles and I know it was serviced at least twice and filter is not too dirty now. It had two small self threading screws in the end cover that could not tighten up very well so I replaced them. But they are on the outside of the filter where they should be, no screws on inside of the filter.
James I have a bore scope and if you want me to send it to you to look inside the motor just let me know. It has been a while since I used it and I will need to check if it will go in our sparkplug hole if you want to look inside the cylinder before pulling it apart.
2016 Wolverine R-Spec EPS, Camo, fender ext. 4000 Moto winch w/syn rope, 14"Method B-locks, 27" Maxxis Vipr 9 & 11's, Full flip windshield, A-arm guards, 2 batts, JBS CVT grind, 16 OD, slugs, purple, JBS/Eibach springs, Autometer Temp Gauge
08 Rhino 700 SE Black Armor, JBS 734 (bbk w/Carillo crank & rod, CP 11:1, deshrouded valves, Raptor springs, Viking cam & FI, MSD, afr Gauge, Unleashed sheave w/JBS OD 18g greased, Purple, slugs, 27" Mudlite XTRs , 6" Chopped , Mishi Rad, ALBA exhaust
Thanks Jim...I have one
Just gotta get the bed off
Sent from my Moto G Play using Tapatalk
James Davis
If you have questions call me!!!
304-673-2602
304-877-3419
Check out our web https://jbsperformance.com/
Email to - jbsperformanceinc@aol.com
Ship to - 131 Davis Ct., Mt. Hope, WV 25880
need to pull mine back off and check it, I just replaced the filter on mine right before James did his
mine was on backwards. James oils them til they drip and wrings them out
I did not have enough oil on mine and it had dust in the intake
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
Bookmarks