-
Help
So I bought the hot rod extreme set up. Came with yellow/gold spring, OD weights and slug kit for clutch. Setup is as follow 2014 Grizzly 700 with 28 inch Zillas, EHS complete airbox/K&N setup and lid Ehs fuel programmer and 2R tip.
Prior to the install of the sheave etc. I could wheelie easily, it would run up to 70mph on a flat road. After the install it wouldn't pull the front wheels off the ground, and would top out at 53. Very disappointed to say the least. So I pulled it apart and went back to stock spring. Threw the weights on scale and they were 16 ounce, so that probably explains some of it on the top end. So with the stock spring back in it will pull the wheels up pretty good but still can't get above 53. So what do I need short of putting my stock parts back on to get where I was instead of backwards with what I thought was a performance mod improvement?
Sent from my SM-G965U1 using Tapatalk
-
Ridin' and Guidin'
did you select the spring and weights?
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
-
Originally Posted by
Timmi
did you select the spring and weights?
No it was what was shipped with the extreme hot rod kit based on the info I entered on the JBS website.
Sent from my SM-G965U1 using Tapatalk
-
Originally Posted by
Grizzly_NY
No it was what was shipped with the extreme hot rod kit based on the info I entered on the JBS website.
Sent from my SM-G965U1 using Tapatalk
Order below
Sent from my SM-G965U1 using Tapatalk
-
Ridin' and Guidin'
I had 16g weights and purple spring in my grizzly
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
-
Originally Posted by
Timmi
I had 16g weights and purple spring in my grizzly
So losing 15mph on the top end is to be expected with the JBS kit is what you are saying?
Sent from my SM-G965U1 using Tapatalk
-
Ridin' and Guidin'
I didn't have the sheave just the weights and spring, mine ran about 65 with 27' tires
sounds like the lighter weights and heavier spring have you geared down lower
Originally Posted by
Grizzly_NY
So losing 15mph on the top end is to be expected with the JBS kit is what you are saying?
Sent from my SM-G965U1 using Tapatalk
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
-
Originally Posted by
Timmi
I didn't have the sheave just the weights and spring, mine ran about 65 with 27' tires
sounds like the lighter weights and heavier spring have you geared down lower
Already put stock spring back in as mentioned, still a pig at top end just trying to get answer if it is the weights, no need to waste more money than I already have at this point.
Sent from my SM-G965U1 using Tapatalk
-
Originally Posted by
Grizzly_NY
Already put stock spring back in as mentioned, still a pig at top end just trying to get answer if it is the weights, no need to waste more money than I already have at this point.
Sent from my SM-G965U1 using Tapatalk
Maybe you have a flopped weight. We're you sure not to let the primary slide together once you put it all back together?
Sent from my XT1254 using Tapatalk
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Ridin' and Guidin'
yea could be a weight flipped , something's not right
" White Shadow " Wolverine X2
JBS Performance Extreme Sheave
JBS Performance Suspension Springs
Team Alba Racing ECU
Rigid Side Shooter Led
Yamaha Cab Enclosure
Bazooka Party Bar
Bookmarks