Nice mower
|
Sponsored By: |
 |
Thanks: 156
Likes: 4,100
Results 1,571 to 1,580 of 4661
Thread: Random Photo & Video Thread
-
09-12-2015, 04:59 AM #1571
- Join Date
- Nov 2014
- Posts
- 344
-
09-12-2015, 09:30 AM #1572
- Join Date
- Dec 2014
- Location
- Oak Hill, WV
- Posts
- 410
Nice! Been looking into getting a zero turn. Oddly I haven't seen a hustler and don't know much about them. Kind of made my mind up on a gravely with Kawasaki motor. Should I change my mind?
-
09-12-2015, 10:19 AM #1573Banned
- Join Date
- Nov 2014
- Location
- Angleton, TX
- Posts
- 3,399
No! Gravely makes a damn good mower. And that Kawi motor is bad ass! I had a Husqvarna 26hp Kohler with 54" cut. The Hustler has a 24hp Kawi with 60" cut and it will run circles around my old one.
Sent from The Green Machine
-
09-12-2015, 01:38 PM #1574
- Join Date
- Sep 2014
- Location
- OHIO
- Posts
- 894
My new mower
Sent from my using Tapatalk
-
09-12-2015, 01:41 PM #1575
- Join Date
- Dec 2013
- Location
- Hayesville,Ohio
- Posts
- 610
For the money you can't beat hustler and toro!! My 2 first picks on a budget for sure. Exmark or ferris if you have the money. Lol. I love my toro and it's one of the best built. Kawasaki motors are hard to beat on mowers.
-
Post Thanks / Like - 0 Thanks, 1 Likes
robleticia liked this post
-
09-12-2015, 01:49 PM #1576Banned
- Join Date
- Nov 2014
- Location
- Angleton, TX
- Posts
- 3,399
-
Post Thanks / Like - 0 Thanks, 2 Likes
-
09-12-2015, 06:40 PM #1577
- Join Date
- Nov 2014
- Location
- Winfield, MO
- Posts
- 568
My wife was driving along last night, and a tree just jumped right out in front of her! I think the tree had been drinking, damn trees
2007 Rhino 660 Special Edition
+4mm Hotrods stroker crank,welded/balanced, CP 10:1 102mm piston, Head studs, Raptor valve springs,Hotcam-Raptor stage one, Stock exhaust with header welds ground out, and billet tip on muffler, black rhino cdi, dragonfire sheave, stock rollers/spring
Jetting-165 main, 50 pilot (2 turns out), swapped washers on needle
-
09-12-2015, 06:46 PM #1578
- Join Date
- Nov 2014
- Location
- Winfield, MO
- Posts
- 568
And 30 minutes down at KBS (my garage lol), looking much better. The previous owner gave me the factory bumper cover when I bought it, and luckily I've kept it. A little twisting, pulling, some new plastic clips, the old bumper cover, and some welding on the knuckle so I can limp it around until I get a new one
2007 Rhino 660 Special Edition
+4mm Hotrods stroker crank,welded/balanced, CP 10:1 102mm piston, Head studs, Raptor valve springs,Hotcam-Raptor stage one, Stock exhaust with header welds ground out, and billet tip on muffler, black rhino cdi, dragonfire sheave, stock rollers/spring
Jetting-165 main, 50 pilot (2 turns out), swapped washers on needle
-
Post Thanks / Like - 0 Thanks, 1 Likes
robleticia liked this post
-
09-12-2015, 06:48 PM #1579
- Join Date
- May 2014
- Posts
- 863
[QUOTE=Krazykevin58;72690]And 30 minutes down at KBS (my garage lol), looking much better. The previous owner gave me the factory bumper cover when I bought it, and luckily I've kept it. A little twisting, pulling, some new plastic clips, the old bumper cover, and some welding on the knuckle so I can limp it around until I get a new one
Damn, as good as new !!!
2012 Camo Teryx4
JBS PoweredUsing Tapatalk
-
09-12-2015, 06:57 PM #1580Most Senior member
- Join Date
- Dec 2013
- Location
- Portland, OR
- Posts
- 1,636
Now, go out there and repair the tree! It must be hurtin'.
Originally Posted by aaronh919
Damn, as good as new !!! Originally Posted by Krazykevin58
____________________________________
...... 2004 660 Camo, "Rhino". And now, also a Wolverine X4. "Wolfy".
|___________________________________
| Two roads diverged in a wood,
| I took the one less traveled by....
| Oh, Oh .
| .............
| ...............
| ............... #
|___________________________________
Reply With Quote
Bookmarks